Logo

Buyonsell, 2000'li yıllardan bu yana sahip olduğu uzmanlık, deneyim ve engin bilgi birikimiyle, Türkiye'nin lider madeni ve motor yağ tedarikçilerinin başında gelmektedir.

İletişim Bilgileri

Adres:

Fevzi Çakmak Mahallesi Ahmet Petekçi Caddesi No:40 42050 Karatay/Konya/Turkiye

E-Mail: export@buyonsell.com
Telefon: +90 332 347 02 02

Sosyal Medya

Logo

klubersynth eg 4

Anasayfa > ürünler > kluber > klubersynth eg 4
Kategoriler
  • ki̇myasallar ve solventler
    • KLUBERSYNTH EG 4

    klubersynth eg 4

    Klübersynth EG 4 is a fully synthetic high-performance gear oil based on polyalphaolefin satisfying the requirements of many gears. Klübersynth EG 4 offers a high scuffing strength of API GL-4. Gears are sufficiently protected against scuffing even at extremely high peak loads, vibrations or oscillations. The good wear protection of the gear components ensures that their calculated service life is achieved, leading to lower maintenance and repair costs.

    Klübersynth EG 4 offers a much longer service life than mineral oils due to the excellent ageing and oxidation resistance of the selected raw materials; thus service intervals can be extended and maintenance costs reduced. The product's low foaming tendency and anti-corrosive properties enable problem-free gear operation.

    Klübersynth EG 4 is neutral towards most sealing materials such as NBR or FKM. Oil leakage leading to contamination is prevented. It also shows good demulsifying behaviour.

    The good viscosity-temperature behaviour supports the formation of a sufficient lubricant film across a wide service temperature range. Therefore, a single viscosity grade can cover both low and high temperatures in many applications. The optimised friction behaviour enabled by the carefully selected base oils reduces power loss and improves gear efficiency.

    By using Klübersynth EG 4 you can benefit from a number of advantages that will help you save costs easily and efficiently. We look forward to hearing from you.

    • Klübersynth EG 4 was especially developed for the lubrication of heavily loaded spur, bevel and planetary gears. It can also be used for the lubrication of worm gears. 
    • Klüberoil EG 4 can also be selected for the lubrication of plain and rolling bearings, all kinds of toothed couplings, chains, guideways, joints, spindles and pumps.
    • Klübersynth EG 4 can be used for immersion, immersion circulation and injection lubrication.
    • The use of drip-feed oilers, brushes, oil cans or suitable automatic lubricating systems is also possible. When using automatic lubricating systems, please note the manufacturer's instructions regarding the maximum permissible viscosity. The low-viscosityvarieties are also used for oil mist lubrication.
    • Klübersynth EG 4 is miscible with mineral oils. However, for the Klübersynth EG 4 oil to deliver its full performance, any residues of a previously used mineral oil should not exceed 5 % in quantity.
    • For use at permanent temperatures of 80 °C max., seals made of NBR may be used. For higher temperatures, seals made of FKM should be chosen. It should be noted that elastomers from one or several manufacturers can behave differently; therefore tests should be performed.
    • For checking the contact pattern during running-in, the inspection paint Klübertop P 39-462 Spray (Art. No. 081295) can be used
    • High scuffing protection
    • Good wear protection
    • Excellent ageing and oxidation resistance
    • Wide service temperature range due to good viscosity-temperature behaviour
    • Low foaming tendency
    • Energy savings due to optimised friction behaviour
    • Very good corrosion protection
    Characteristics  Klübersynth EG 4-680  Klübersynth EG 4-1000
    Article number 012224 012225
    Service temperature, lower limit -25 °C -15 °C
    Service temperature, upper limit 140 °C 120 °C
    Density, DIN 51757, 20°C approx. 0.89 g/cm³  approx. 0.89 g/cm³
    Flash point, DIN EN ISO 2592, Cleveland open cup ≥ 200 °C ≥ 200 °C
    Foam test, ISO 6247 / ASTM D892, 24°C, sequence I ≤ 100/10 ml ≤ 100/10 ml
    Foam test, ISO 6247 / ASTM D892, 24°C, sequence III ≤ 100/10 ml ≤ 100/10 ml
    Foam test, ISO 6247 / ASTM D892, 93.5°C, sequence II ≤ 100/10 ml ≤ 100/10 ml
    ISO viscosity grade, DIN ISO 3448, ISO VG 680 1000
    Kinematic viscosity, DIN EN ISO 3104 / DIN 51562-1 / ASTM D445 / ASTM D7042, 100°C approx. 53.4 mm²/s approx. 71.3 mm²/s
    Kinematic viscosity, DIN EN ISO 3104 / DIN 51562-1 / ASTM D445 / ASTM D7042, 40°C approx. 680 mm²/s approx. 1000 mm²/s
    Viscosity index, DIN ISO 2909 ≥ 130 ≥ 130
    Pour point, DIN ISO 3016 ≤ -30 °C ≤ -24 °C
    API scuffing load capacity API GL 4 API GL 4
    FAG FE8 rolling bearing test, DIN 51819-3, D-7.5 / 80-80, wear of cage ≤ 200 mg  ≤ 200 mg
    FAG FE8 rolling bearing test, DIN 51819-3, D-7.5 / 80-80, wear of rolling elements ≤ 30 mg ≤ 30 mg
    FZG scuffing test, DIN ISO 14635-1, based on standard, A / 16.6 / 90, failure load stage ≥ 12 ≥ 12
    FZG scuffing test, DIN ISO 14635-1, A / 8.3 / 90, failure load stage ≥ 14 ≥ 14
    Minimum shelf life from the date of manufacture - in a dry, frost-free place and in the unopened original container, approx. 60 months 60 months

     

    klubersynth-eg-4.pdf