Logo

Buyonsell is one of the leading lubricant and engine oil suppliers in Turkey with its expertise, experience and vast knowledge since the 2000s.

Contact Information

Address:

Fevzi Çakmak Mahallesi Ahmet Petekçi Caddesi No:40 42050 Karatay/Konya/Turkiye

E-Mail: export@buyonsell.com
Telephone: +90 332 347 02 02

Social Media

Logo

kluberpaste 46 mr 401

Homepage > products > kluber > kluberpaste 46 mr 401
Categories
  • chemicals and solvents
    • KLUBERPASTE 46 MR 401
    KLUBERPASTE 46 MR 401

    kluberpaste 46 mr 401

    Light-coloured high-pressure lubricating paste.

    Klüberpaste 46 MR 401 is a multipurpose lubricating paste with selected base oils, lithium soap and special solid lubricant additives.

    This versatile multipurpose paste has a wide service temperature range and shows good pressure absorption capacity as well as neutral behaviour towards non-ferrous metals, many plastics and elastomers.

    • Klüberpaste 46 MR 401 is especially suitable as an assembly lubricant in frictional connections and for thin-film lubrication of all friction points subject to very high pressure loads, low sliding speed, high wear, Stick-Slip and tribo-corrosion.
    • Typical applications include: press fit assembly of pins and bolts, mounting of rolling bearings, wheels and flanges, lubrication of rolling and plain bearings operating at very low speeds.
    • Klüberpaste 46 MR 401 is also suitable to prevent running-in damage and stick-slip in components such as threaded spindles, spline shafts, ball and socket joints and rod end bearings.
    • Its good compatibility with plastics facilitates the lubrication of radial shaft seals (o-rings, v-rings, sealing cups) made of rubber-elastic materials for extended lifetime.
    • Owing to the many different elastomer and plastic compositions, we recommend compatibility be checked prior to series application.
    • Before applying Klüberpaste 46 MR 401 it is important to clean the contact surfaces and remove any solvent residues with a lint-free, dry cloth.
    • Klüberpaste 46 MR 401 can be easily applied to the entire surface in a thin layer with a spatula. It is important to avoid overlubrication.
    • Before applying the paste to a plastic material we recommend undertaking a materials compatibility test.
    • The friction values indicated on page 2 in the Section Product Data were determined with two different materials. Other materials/surfaces have to be checked accordingly.
    • Easy assembly and disassembly of highly loaded frictional connections
    • Prevents premature material ageing caused by tribo-corrosion and stick slip
    • Can be used with many material combinations, including plastics and elastomers
    Characteristics Klüberpaste 46 MR 401
    Article number 005108
    Colour space white
    Service temperature, lower limit -40 °C
    Service temperature, upper limit  150 °C
    Density, Klüber method: PN 024, 20°C approx. 1.23 g/cm³
    Worked penetration, DIN ISO 2137 / ASTM D217, 25°C, lower limit 300 0.1 mm
    Worked penetration, DIN ISO 2137 / ASTM D217, 25°C, upper limit 340 0.1 mm
    Copper corrosion, DIN 51811, 24 h, 100°C 1 - 100 - 24 corrosion degree
    SKF-EMCOR, DIN 51802, Klüber method: distilled water, 168 h  ≤ 1 corrosion degree
    Flow pressure, DIN 51805-2, -40°C  ≤ 1600 mbar
    Dropping point, DIN ISO 2176 / IP 396 ≥ 185 °C
    Four-ball tester, welding load, DIN 51350-4 ≥ 4600 N
    Friction coefficient screw test, hexagon bolts M10 x 30-8.8, DIN EN ISO 4017, tightening speed n = 5 min⁻¹, number of screws = 20, nut M10-8, plain and degreased, face material 42CrMo4 with roughness Ra 1.6, tightening torque MA = 50 Nm, averaged bearing surface friction coefficient (initial tightening), external test 0.14
    Friction coefficient screw test, hexagon bolts M10 x 30-8.8, DIN EN ISO 4017, tightening speed n = 5 min⁻¹, number of screws = 20, nut M10-8, plain and degreased, face material 42CrMo4 with roughness Ra 1.6, tightening torque MA = 50 Nm, averaged thread friction coefficient (initial tightening), external test 0.12
    Friction coefficient screw test, hexagon bolts M10 x 30-8.8, DIN EN ISO 4017, tightening speed n = 5 min⁻¹, number of screws = 20, nut M10-8, plain and degreased, face material 42CrMo4 with roughness Ra 1.6, tightening torque MA = 50 Nm, standard deviation (S) of averaged bearing surface friction coefficient (initial tightening), external test 0.005
    Friction coefficient screw test, hexagon bolts M10 x 30-8.8, DIN EN ISO 4017, tightening speed n = 5 min⁻¹, number of screws = 20, nut M10-8, plain and degreased, face material 42CrMo4 with roughness Ra 1.6, tightening torque MA = 50 Nm, standard deviation (S) of averaged thread friction coefficient (initial tightening), external test 0.008
    Minimum shelf life from the date of manufacture - in a dry, frost-free place and in the unopened original container, approx. 36 months

     

    kluberpaste-46-mr-401.pdfkluberpaste-46-mr-401-en.pdf
    kluberpaste-46-mr-401.pdfkluberpaste-46-mr-401-en.pdf