Logo

Buyonsell is one of the leading lubricant and engine oil suppliers in Turkey with its expertise, experience and vast knowledge since the 2000s.

Contact Information

Address:

Fevzi Çakmak Mahallesi Ahmet Petekçi Caddesi No:40 42050 Karatay/Konya/Turkiye

E-Mail: export@buyonsell.com
Telephone: +90 332 347 02 02

Social Media

Logo

summit sh

Homepage > products > kluber > summit sh
Categories
  • chemicals and solvents
    • SUMMIT SH

    summit sh

    Synthetic air compressor oils for oil change intervals up to 10,000 operating hours.

    Klüber Summit SH oils are air compressor oils based on synthetic hydrocarbon and additives. They can be mixed with mineral oils and synthetic hydrocarbon oils, however are not miscible with polyglycol oils.

    • Klüber Summit SH oils have been designed especially for the lubrication of highly loaded, oil-injected screw-type compressors with oil change intervals up to 10,000 operating hours.
    • Klüber Summit SH oils can also be used for compressors that were previously run with mineral oils. They are neutral towards most elastomer seals used in air compressors, therefore leakage is not to be expected.
    • Klüber Summit SH 32 is especially suitable for centrifugal compressors and Klüber Summit SH 100 for reciprocating piston compressors.
    • Klüber Summit SH oils offer excellent oxidation stability due to the synthetic base oil, thus minimizing oxidation residues in the compressors and extending oil change intervals and the service life of oil filters and separators. Special inhibitors contained in the oils keep the inside of compressors clean.
    • Owing to the evaporation stability of the base oil, the oil vapour content in the compressed air can be considerably reduced compared to conventional mineral oils. This contributes to a reduction of oil consumption and clean compressed air; gumming of pneumatic valves in the compressed air circuit can be prevented as well due to the low oil content of the Klüber Summit SH oils.
    • Low maintenance and operating costs due to extended oil change intervals up to 10,000 operating hours in oil-injected screw-type compressors
    • Easy compressor oil conversion due to neutral behaviour of oils towards seals
    • Low tendency to evaporation and thus low impact of the oil vapour on the compressed air
    • Longer servie life of the oil filters, activated carbon filters and oil separators
    • Low formation of oxidation residues in the oil circuit, reduced operating costs due to extended oil filter and separator life
    • Reduction of energy costs due to more energy efficient operation
    • Surpasses the requirements of DIN 51506-VDL and ISO 6743-3 L-DAJ (VG 32/46/55/68) / L-DAB (VG 100)
    Characteristics Klüber Summit SH 32 Klüber Summit SH 46 Klüber Summit SH 55 Klüber Summit SH 68 Klüber Summit SH 100
    Article number  050004 050005 050160 050006 050007
    Appearance clear clear clear clear clear
    Colour space colourless colourless colourless colourless colourless
    Demulsifying capacity, DIN ISO 6614 /ASTM D1401, 54°C 40-37-3 (30) ml (min) 40-37-3 (30) ml (min) 40-37-3 (30) ml (min) 40-37-3 (30) ml (min)  -
    Demulsifying capacity, DIN ISO 6614 /ASTM D1401, 82°C  -  -  -  - 40-37-3 (30) ml (min)
    Density, DIN 51757, 20°C approx. 0.85 g/cm³ approx. 0.85 g/cm³ approx. 0.86 g/cm³ approx. 0.86 g/cm³ approx. 0.86 g/cm³
    Flash point, DIN EN ISO 2592, Cleveland open cup ≥ 230 °C ≥ 240 °C ≥ 240 °C ≥ 240 °C ≥ 240 °C
    Foam test, ISO 6247 / ASTM D892, 24°C, sequence I 50/0 ml 50/0 ml 50/0 ml 50/0 ml 50/0 ml
    Foam test, ISO 6247 / ASTM D892, 24°C, sequence III 50/0 ml 50/0 ml 50/0 ml 50/0 ml 50/0 ml
    Foam test, ISO 6247 / ASTM D892, 93.5°C, sequence II 50/0 ml 50/0 ml 50/0 ml 50/0 ml 50/0 ml
    Kinematic viscosity, DIN EN ISO 3104 / DIN 51562-1 / ASTM D445 / ASTM D7042, 100°C approx. 5.8 mm²/s approx. 7.7 mm²/s approx. 8.7 mm²/s approx. 9.8 mm²/s approx. 13.1 mm²/s
    Kinematic viscosity, DIN EN ISO 3104 / DIN 51562-1 / ASTM D445 / ASTM D7042, 40°C approx. 32 mm²/s approx. 46 mm²/s  approx. 55 mm²/s approx. 68 mm²/s approx. 100 mm²/s
    Viscosity index, DIN ISO 2909 ≥ 115 ≥ 115 ≥ 115 ≥ 115 ≥ 115
    Copper corrosion, DIN EN ISO 2160, 24 h, 100°C 1 - 100 - 24 corrosion degree 1 - 100 - 24 corrosion degree 1 - 100 - 24 corrosion degree 1 - 100 - 24 corrosion degree 1 - 100 - 24 corrosion degree
    Pour point, DIN ISO 3016 ≤ -51 °C ≤ -36 °C ≤ -36 °C ≤ -36 °C ≤ -33 °C
    Minimum shelf life from the date of manufacture - in a dry, frost-free place and in the unopened original container, approx. 60 months 60 months 60 months 60 months 60 months

     

    kluber-summit-sh.pdfkluber-summit-sh-en.pdf
    kluber-summit-sh.pdfkluber-summit-sh-en.pdf