SUMMIT SB

Klüber Summit SB oils have been especially designed for screw-type compressors subject to high loads. They are used for oil change intervals up to 8,000 operating hours in air compressors.
Klüber Summit SB oils can be used for compressors that were previously run with mineral oils. Klüber Summit SB oils are neutral towards most elastomer seals used in air compressors, therefore leakage is not to be expected.
Klüber Summit SB oils offer good oxidation stability due to the synthetic base oil content, thus minimising oxidation residues in the compressors and extending oil change intervals and the service life of oil filters and separators. Special inhibitors contained in the oil keep the inside of compressors clean and ensure a high efficiency.
Owing to the evaporation stability of the base oil, the oil vapour content in the compressed air can be reduced several-fold compared to conventional mineral oils. This contributes to a reduction of oil consumption and clean compressed air; it also helps to prevent gumming of pneumatic valves in the compressed air circuit.
When selecting the oil viscosity for air compressors please observe the manufacturers’ instructions.
When switching a used compressor to Klüber Summit SB oils, drain the old oil from the whole circuit while still warm. We also recommend changing all oil filters and separators. Then refill the compressor with Klüber Summit SB oil.
When switching from mineral oil to a Klüber Summit SB oil please consider that the compressor may contain oxidation residues in the form of blackened or contaminated oil. As such residues can affect the service life of the fresh Klüber Summit SB oil, the compressor should be cleaned using the Klüber Summit Varnasolv conditioner.
For further information, please consult the Klüber Summit Varnasolv product information leaflet or contact Klüber Lubrication.
After switching to a Klüber Summit SB oil we recommend determining the oil change interval through an oil analysis

Low maintenance and operating costs due to extended oil change intervals up to 8,000 operating hours in oil-injected screw-type compressors
Easy compressor oil conversion due to neutral behaviour of oils towards seals
Low tendency to evaporation ensures clean (oil-free) compressed air and oil-free compressed air ductwork system, no unnecessary cleaning or failure of gummed pneumatic valves
Low formation of oxidation residues in the oil circuit, reduced operating costs due to extended oil filter and separator life
Surpasses the requirements of DIN 51506-VDL and ISO 6743-3 L-DAJ

Characteristics	Klüber Summit SB 46	Klüber Summit SB 68
Article number	050080	050081
Appearance	clear	clear
Colour space	yellow	yellow
Demulsifying capacity, DIN ISO 6614 /ASTM D1401, 54°C	40-37-3 (30) ml (min)	40-37-3 (30) ml (min)
Density, DIN 51757, 20°C	approx. 0.87 g/cm³	approx. 0.87 g/cm³
Flash point, DIN EN ISO 2592, Cleveland open cup	≥ 240 °C	≥ 260 °C
Foam test, ISO 6247 / ASTM D892, 24°C, sequence I	≤ 50/0 ml	≤ 50/0 ml
Foam test, ISO 6247 / ASTM D892, 24°C, sequence III	≤ 50/0 ml	≤ 50/0 ml
Foam test, ISO 6247 / ASTM D892, 93.5°C, sequence II	≤ 50/0 ml	≤ 50/0 ml
Kinematic viscosity, DIN EN ISO 3104 / DIN 51562-1 / ASTM D445 / ASTM D7042, 100°C	approx. 7.6 mm²/s	approx. 9.8 mm²/s
Kinematic viscosity, DIN EN ISO 3104 / DIN 51562-1 / ASTM D445 / ASTM D7042, 40°C	approx. 46 mm²/s	approx. 68 mm²/s
Viscosity index, DIN ISO 2909	≥ 100	≥ 100
Copper corrosion, DIN EN ISO 2160, 3 h, 100°C	1 - 100 - 3 corrosion degree	1 - 100 - 3 corrosion degree
Pour point, DIN ISO 3016	≤ -39 °C	≤ -39 °C
Minimum shelf life from the date of manufacture - in a dry, frost-free place and in the unopened original container, approx.	36 months	36 months

kluber-summit-sb.pdf kluber-summit-sb-en.pdf

Name and Surname

Company Name

Your E-Mail Address

Your Telephone Number

Your Message

I have read and understood the Kvkk and Information Text.

Contact Information

Social Media

Categories

summit sb